RUMBA32 32-bit 3D Printer Mainboard Compatible Marlin 2.0 + 6Pcs TMC2100 Super Silent Driver Kit

RUMBA32 32-bit 3D Printer Mainboard Compatible Marlin 2.0 + 6Pcs TMC2100 Super Silent Driver Kit

Image
R 2,909.99
Successful pre-order.Thanks for contacting us!
If you want know more about Rumba32 Control Board , please click ID:1653473

Specification for Rumba32 Control Board:

Input voltage: 12-24V
Step driver: 6 (SPI socket type stepstick supported)
MOSFET output: 6
Maximum bed current: 20A
Maximum heater current: 5A
Number of thermistor connections: 5
Limit switch: 6
Firmware: Marlin bufix-2.0

About TMC2100V1.3 mute driver:

As shown in the figure: If you need to adjust the mode of the 2100 module, you need to use the soldering iron, according to the table will be listed in the corresponding pin and adjacent pad can be connected.



1. Drive current algorithm: i = Vref * 1.9 / 2.5, the default Vref is about 0.65v, so the default current is 0.5A, and the maximum current is 1A!
2. Vref measures the voltage at Gnd and the middle of the potentiometer.
3. Be sure not to connect the motor when measuring the voltage, otherwise it is easy to burn the drive.
4. When measuring the voltage, you should connect the power, and do not just connect the USB power supply.
Pay attention to the direction, do not insert it backwards!

Using Methos:

1. When using on Ramps1.4 or MKS Gen, please remove the 3 jumper caps under the socket
2. Pay attention to direction
3.The heat sink is directly attached to the PCB
4. The direction of the motor is exactly the opposite of A4988 and DRV8825. If you want to directly replace 4988, please adjust the firmware or adjust the motor wiring.

 
Package included:

1 x Rumba32 Control Board 
1 x USB Data Cable
6 x TMC2100
6 x Fin 
1 x Screwdriver 
 






If you want know more about Rumba32 Control Board , please click ID:1653473

Specification for Rumba32 Control Board:

Input voltage: 12-24V Step driver: 6 (SPI socket type stepstick supported) MOSFET output: 6 Maximum bed current: 20A Maximum heater current: 5A Number of thermistor connections: 5 Limit switch: 6 Firmware: Marlin bufix-2.0

About TMC2100V1.3 mute driver:

As shown in the figure: If you need to adjust the mode of the 2100 module, you need to use the soldering iron, according to the table will be listed in the corresponding pin and adjacent pad can be connected.



1. Drive current algorithm: i = Vref * 1.9 / 2.5, the default Vref is about 0.65v, so the default current is 0.5A, and the maximum current is 1A!
2. Vref measures the voltage at Gnd and the middle of the potentiometer.
3. Be sure not to connect the motor when measuring the voltage, otherwise it is easy to burn the drive.
4. When measuring the voltage, you should connect the power, and do not just connect the USB power supply.
Pay attention to the direction, do not insert it backwards!

Using Methos:

1. When using on Ramps1.4 or MKS Gen, please remove the 3 jumper caps under the socket
2. Pay attention to direction
3.The heat sink is directly attached to the PCB
4. The direction of the motor is exactly the opposite of A4988 and DRV8825. If you want to directly replace 4988, please adjust the firmware or adjust the motor wiring.

 
Package included:

1 x Rumba32 Control Board  1 x USB Data Cable
6 x TMC2100 6 x Fin  1 x Screwdriver